Modeling for reorientation and potential of enhanced oil recovery in refracturing
Abstract view|464|times PDF download|111|times
Abstract
Reorientation of fractures and high production improvement are observed and illustrated by fields and theoretical researches. During the refracturing treatments, it is important to get familiar with the enhanced oil recovery mechanics of fracture reorientation and distribution of residual oil. Mechanisms of fracture reorientation are discussed in order to design the parameters of reoriented fractures in numerical simulation. To furtherly evaluate the oil recovery of different angles of reoriented fractures, geological and numerical models are simulated using data of the actual reservoir with rhombus inverted nine spot well pattern, different angles of reoriented fracture are designed for both corner and edge wells to obtain the enhanced oil recovery. Results show that potential of production increase is highly impacted by the well pattern and angles of fractures and meanwhile impacted by distribution of residual oil and formation properties. Oil enhancement potential is significantly different with fracture reorientation angles in refracturing treatment: cumulative produced oil for corner wells is symmetrical around the angle of 0o and reaches the highest at the angles of positive and negative 23o; for the edge wells, it is also symmetrical around the angle of 0o while reaches the highest cumulative oil at the angles of positive and negative 90o. The difference shows that optimal angles exist for reoriented fractures during refracturing design and with proper induced reoriented fractures, more oil will be recovered for field restimulation treatments.
Cited as: Lu, M., Su, Y., Zhan, S., Almarbat, A. Modeling for reorientation and potential of enhanced oil recovery in refracturing. Advances in Geo-Energy Research, 2020, 4(1): 20-28, doi: 10.26804/ager.2020.01.03
Keywords
Full Text:
PDFReferences
Barree, R.D., Miskimins, J.L., Svatek, K.J. Reservoir and completion considerations for the refracturing of horizontal wells. SPE Prod. Oper. 2017, 33(1): 111.
Berchenko, I., Detournay, E. Deviation of hydraulic fractures through poroelastic stress changes induced by fluid injection and pumping. Int. J. Rock Mech. Min. Sci. 1997, 34(6): 1009-1019.
Bratov, V. Numerical models for hydraulic refracturing on vertical oil wells. Int. J. Eng. Technol. 2018, 7(4.26): 279-284.
Dahi-Taleghani, A., Olson, J.E. Numerical modeling of multi-stranded hydraulic fracture propagation: Accounting for the interaction between induced and natural fractures. SPE J. 2011, 16(3): 575-581.
Elbel, J.L., Mack, M.G. Refracturing: Observations and theories. Paper SPE 25464 Presented at SPE Production Operations Symposium, Oklahoma City, Oklahoma, 21-23 March, 1993.
Guo, T., Gong, F., Qu, Z., et al. Study on fracture initiation mechanisms of hydraulic refracturing guided by directional boreholes. J. Energy Resour. Technol. 2018, 140(8): 084901.
Hubbert, M.K., Willis, D.G. Mechanics of hydraulic fracturing. Trans. AIME 1957, 210: 153-168.
Ishida, T., Fujito, W., Yamashita, H., et al. Crack expansion and fracturing mode of hydraulic refracturing from acoustic emission monitoring in a small-scale field experiment. Rock Mech. Rock Eng. 2019, 52(2): 543-553.
Lolon, E.P., Mayrhofer, M.J., Garcia, I. Integrated fracture and production modeling study in the lower cotton valley sands, Northern Louisiana. Paper SPE 115467 Presented at SPE Annual Technical Conference and Exhibition, Denver, Colorado, USA, 21-24 September, 2008.
Preiksaitis, M., Baig, A., Bowman-Young, S., et al. Identifying re-stimulation effectiveness by utilizing microseismic attributes. Paper SPE 2461172 Presented at the Unconventional Resources Technology Conference, San Antonio, Texas, 1-3 August, 2016.
Reeves, S.R., Hill, D.G., Hopkins, C.W., et al. Restimulation technology for tight gas sand wells. Paper SPE 56482 Presented at SPE Annual Technical Conference and Exhibition held in Houston, Texas, USA, 3-6 October, 1999.
Roussel, N.P., Sharma, M.M. Quantifying transient effects in altered-stress refracturing of vertical wells. SPE J. 2010, 15(3): 770-782.
Roussel, N.P., Sharma, M.M. Optimizing fracture spacing and sequencing in horizontal-well fracturing. SPE Prod. Oper. 2011, 26(2): 173-184.
Roussel, N.P., Sharma, M.M. Role of stress reorientation in the success of refracture treatments in tight gas sands. SPE Prod. Oper. 2012, 27(4): 346-355.
Roussel, N.P., Sharma, M.M. Selecting candidate wells for refracturing using production data. SPE Prod. Oper. 2013, 28(1): 36-45.
Sallee, W.L., Rugg, F.E. Artificial formation fracturing in Southern Oklahoma and North-Central Texas. AAPG Bull. 1953, 37(11): 2539-2550.
Shah, M., Subhash, S., Anirbid, S. A comprehensive overview on recent developments in refracturing technique for shale gas reservoirs. J. Nat. Gas Sci. Eng. 2017, 46: 350-364.
Siebrits, E., Elbel, J.L., Detournay, E., et al. Parameters affecting azimuth and length of a secondary fracture during a refracture treatment. Paper SPE 48928 Presented at SPE Annual Technical Conference and Exhibition, New Orleans, USA, 27-30 September, 1998.
Teng, B., Li, H.A. A semi-analytical model for characterizing transient flow behavior of reoriented refractures. J. Pet. Sci. Eng. 2019, 177: 921-940.
Vincent, M. Restimulation of unconventional reservoirs: When are refracs beneficial. J. Can. Pet. Technol. 2011, 50(5): 36-52.
Warpinski, N.R., Branagan, P.T. Altered stress fracturing. J. Pet. Technol. 1989, 41(9): 990-997.
Warpinski, N.R., Clark, J.A., Schmidt, R.A., et al. Laboratory investigation on the effect of in-situ stresses on hydraulic fracture containment. Soc. Pet. Eng. J. 1982, 22(3): 333-340.
Zhang, G., Chen, M. Study of the optimal timing for refracturing. Pet. Sci. Technol. 2009a, 27(10): 969-983.
Zhang, G., Chen, M. Relationship between production and initiation location of new fractures in re-fractured well. Journal of Liaoning Technical University (Natural Science) 2009b, 28(3): 407-409. (in Chinese)
Zhang, G., Chen, M. Dynamic fracture propagation in hydraulic re-fracturing. J. Pet. Sci. Eng. 2010, 70(3): 266-272.
Zhang, G., Chen, M., Yao, F. Study on optimal refracturing timing in anisotropic formation and its influencing factors. Acta Petrolei Sinica 2008, 29: 885-888. (in Chinese)
Refbacks
- There are currently no refbacks.
Copyright (c) 2020 The Author(s)
This work is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.